void TIM2_Master__TIM3_Slave_Configuration(u32 PulseFrequency)

{

    TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;

    TIM_OCInitTypeDef       TIM_OCInitStructure;

    u16 nPDTemp ;

    /* -----------------------------------------------------------------------

    TIMx Configuration: generate 4 PWM signals with 4 different duty cycles:

    TIMxCLK = 72 MHz, Prescaler = 0x0, TIMx counter clock = 72 MHz

    TIMx ARR Register = 0 => TIMx Frequency = TIMx counter clock/(ARR + 1)

    TIMx Frequency = 72MHz.

    ----------------------------------------------------------------------- */

    TIM_Cmd(TIM2, DISABLE);

    nPDTemp = 72000000UL/PulseFrequency;    

// 时基配置：配置PWM输出定时器——TIM2

    /* Time base configuration */

    TIM_TimeBaseStructure.TIM_Period          = nPDTemp-;

    TIM_TimeBaseStructure.TIM_Prescaler       = ;

    TIM_TimeBaseStructure.TIM_ClockDivision   = ;

    TIM_TimeBaseStructure.TIM_CounterMode     = TIM_CounterMode_Up;

    TIM_TimeBaseStructure.TIM_RepetitionCounter = ;

    TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);

// 输出配置：配置PWM输出定时器——TIM2

    /* PWM1 Mode configuration: Channel1 */

    TIM_OCInitStructure.TIM_OCMode            = TIM_OCMode_PWM1;

    TIM_OCInitStructure.TIM_OCPolarity        = TIM_OCPolarity_High;

    TIM_OCInitStructure.TIM_OutputState       = TIM_OutputState_Enable;

    TIM_OCInitStructure.TIM_Pulse             = nPDTemp>>;//50%

    TIM_OC1Init(TIM2, &TIM_OCInitStructure);

    TIM_OC1PreloadConfig(TIM2, TIM_OCPreload_Enable);

// 时基配置：配置脉冲计数寄存器——TIM3

    TIM_TimeBaseStructure.TIM_Period        = 0xFFFF;

    TIM_TimeBaseStructure.TIM_Prescaler     = ;

    TIM_TimeBaseStructure.TIM_ClockDivision = ;

    TIM_TimeBaseStructure.TIM_CounterMode   = TIM_CounterMode_Up;

    TIM_TimeBaseStructure.TIM_RepetitionCounter = ;

    TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);    

    /* Output Compare Active Mode configuration: Channel1 */

    TIM_OCInitStructure.TIM_OCMode                        = TIM_OCMode_Inactive;

    TIM_OCInitStructure.TIM_OCPolarity                = TIM_OCPolarity_High;

    TIM_OCInitStructure.TIM_OutputState                = TIM_OutputState_Enable;

    TIM_OCInitStructure.TIM_Pulse                        = 0xFFFF; // 这里的配置值意义不大

    TIM_OC1Init(TIM3, &TIM_OCInitStructure);

// 配置TIM2为主定时器

    /* Select the Master Slave Mode */

    TIM_SelectMasterSlaveMode(TIM2, TIM_MasterSlaveMode_Enable);

    /* Master Mode selection */

    TIM_SelectOutputTrigger(TIM2, TIM_TRGOSource_Update);

// 配置TIM3为从定时器

    /* Slave Mode selection: TIM3 */

    TIM_SelectSlaveMode(TIM3, TIM_SlaveMode_Gated);

    TIM_SelectInputTrigger(TIM3, TIM_TS_ITR1);

    TIM_ITConfig(TIM3, TIM_IT_CC1, ENABLE);

    TIM_Cmd(TIM2, DISABLE);

    TIM_Cmd(TIM3, DISABLE);

}

中断服务程序如下：

u8  TIM2_Pulse_TIM3_Counter_OK = ;

void TIM3_IRQHandler(void)

{

    if (TIM_GetITStatus(TIM3, TIM_IT_CC1) != RESET)

    {

        TIM_ClearITPendingBit(TIM3, TIM_IT_CC1);    // 清除中断标志位

        TIM_Cmd(TIM2, DISABLE); // 关闭定时器

        TIM_Cmd(TIM3, DISABLE); // 关闭定时器

        TIM2_Pulse_TIM3_Counter_OK = ;

    }

}

应用程序为：

u16 pulsecnt = ;

void main(void)

{

    SystemSetup();        // 初始化内核和外设

    TIM2_Master__TIM3_Slave_Configuration();//配置TIM2的脉冲输出为10k

    while()

    {

        TIM_ITConfig(TIM3, TIM_IT_CC1, DISABLE);        /* TIM enable counter */

        TIM_Cmd(TIM3, ENABLE);

        TIM3->CCR1  = pulsecnt;

        TIM3->CNT   = ;

        TIM_ITConfig(TIM3, TIM_IT_CC1, ENABLE);

        TIM_Cmd(TIM2, ENABLE);    /* TIM enable counter */

        while(TIM2_Pulse_TIM3_Counter_OK  == );

    }

}