Performance Tweaks
Jump to navigationJump to search
Contents
Introduction
This page is intended to be a collection of various performance tips/tweaks to help you get the most from your KVM virtual servers.
General
VirtIO
Use virtIO for disk and network for best performance.
- Linux has the drivers built in since Linux 2.6.24 as experimental, and since Linux 3.8 as stable
- FreeBSD has the drivers built in since 9.0
- Windows requires the Windows VirtIO Drivers to be downloaded and installed manually
Disk Cache
| Note: The information below is based on using raw volumes, other volume formats may behave differently. |
Small Overview
Note: The overview below is dependent of the specific hardware used, i.e. a HW Raid with a BBU backed disk cache works just fine with 'writeback' mode, so take it just as an general overview.
| Mode | Host Page Cache | Disk Write Cache | Notes |
|---|---|---|---|
| none | disabled | enabled | balances performance and safety (better writes) |
| writethrough | enabled | disabled | balances performance and safety (better reads) |
| writeback | enabled | enabled | fast, can loose data on power outage depending on hardware used |
| directsync | disabled | disabled | safest but slowest (relative to the others) |
| unsafe | enabled | enabled | doesn't flush data, fastest and unsafest |
cache=none seems to be the best performance and is the default since Proxmox 2.X.
host don't do cache.
guest disk cache is writeback
Warn : like writeback, you can loose datas in case of a powerfailure
you need to use barrier option in your linux guest fstab if kernel < 2.6.37 to avoid fs corruption in case of powerfailure.
This mode causes qemu-kvm to interact with the disk image file or block device with O_DIRECT semantics, so the host page cache is bypassed
and I/O happens directly between the qemu-kvm userspace buffers and the storage device. Because the actual storage device may report
a write as completed when placed in its write queue only, the guest's virtual storage adapter is informed that there is a writeback cache,
so the guest would be expected to send down flush commands as needed to manage data integrity.
Equivalent to direct access to your hosts' disk, performance wise.
cache=writethrough
host do read cache
guest disk cache mode is writethrough
Writethrough make a fsync for each write. So it's the more secure cache mode, you can't loose data. It's also the slower.
This mode causes qemu-kvm to interact with the disk image file or block device with O_DSYNC semantics,
where writes are reported as completed only when the data has been committed to the storage device.
The host page cache is used in what can be termed a writethrough caching mode.
The guest's virtual storage adapter is informed that there is no writeback cache, so the guest would not need to send down
flush commands to manage data integrity. The storage behaves as if there is a writethrough cache.
cache=directsync
host don't do cache.
guest disk cache mode is writethrough
similar to writethrough, a fsync is made for each write.
This mode causes qemu-kvm to interact with the disk image file or block device with both O_DSYNC and O_DIRECT semantics,
where writes are reported as completed only when the data has been committed to the storage device, and when it is also desirable to bypass the host page cache.
Like cache=writethrough, it is helpful to guests that do not send flushes when needed.
It was the last cache mode added, completing the possible combinations of caching and direct access semantics.
cache=writeback
host do read/write cache
guest disk cache mode is writeback
Warn : you can loose datas in case of a powerfailure
you need to use barrier option in your linux guest fstab if kernel < 2.6.37 to avoid fs corruption in case of powerfailure.
This mode causes qemu-kvm to interact with the disk image file or block device with neither O_DSYNC nor O_DIRECT semantics,
so the host page cache is used and writes are reported to the guest as completed when placed in the host page cache,
and the normal page cache management will handle commitment to the storage device.
Additionally, the guest's virtual storage adapter is informed of the writeback cache,
so the guest would be expected to send down flush commands as needed to manage data integrity.
Analogous to a raid controller with RAM cache.
For read cache memory: try to add more memory in your guest, they already do the job with their buffer cache
cache=writethrough or directsync can be also quite fast if you have a SAN or HW raid controller with battery backed cache.
Using qcow2 backed disks and either cache=directsync or writethrough can make things slower.
some interestings articles :
cache mode and fsync : KVM storage performance and cache settings on Red Hat Enterprise Linux 6.2
OS Specific
Windows
USB Tablet Device
Disabling the USB tablet device in windows VMs can reduce idle CPU usage and reduce context switches. This can be done on the GUI. You can use vmmouse to get the pointer in sync (load drivers inside your VM). [1]
Use raw disk image and not qcow2
Consider using raw image or partition for a partition, especially with Microsoft SQL database files because qcow2 can be very slow under such type of load.
Trace Flag T8038 with Microsoft SQL Server
Setting the trace flag -T8038 will drastically reduce the number of context switches when running SQL 2005 or 2008.
To change the trace flag:
- Open the SQL server Configuration Manager
- Open the properties for the SQL service typically named MSSQLSERVER
- Go to the advanced tab
- Append ;-T8038 to the end of the startup parameters option
For additional references see: Proxmox forum
Do not use the Virtio Balloon Driver
The Balloon driver has been a source of performance problems on Windows, you should avoid it. (see [SOLVED] Hyper-Threading vs No Hyper-Threading; Fixed vs Variable Memory | Proxmox Support Forum for the discussion thread)