了解更多关于bootloader 的C语言实现，请加我QQ: 1273623966 （验证信息请填 bootloader）,欢迎咨询或定制bootloader（在线升级程序）。
从15年12月份以来我的空余时间都在折腾15年底买的PIC32MZ EC Starter kit。并陆续写了十多篇随笔记录我折腾的历程。最近新完成的是用C语言实现了PIC32的UART bootloader, 采用串口通信，适用于Microchip的PIC32MZ EC，稍作对应的修改也可适用于PIC32MX, PIC32MZ EF等。Uart bootloader是用XC32编译的，电脑端的通信软件是用超级终端--HyperTerminal (也可以使用SecureCRT). 和之前我写的HyperBootloader_PIC16/PIC18/dsPIC很类似，算是一个家族系列之一。为保证家族特性，我命其名为HyperBootloader_PIC32
BOOTLOADER PLACEMENT
HyperBootloader_PIC32 序放在引导闪存存储器中，如下图所示。
BOOTLOADER LINKER SCRIPT
由于需要将bootloader放置在特定位置，我们不能使用默认的linker script. 我们需要修改linker script来放置bootloader, 以下是修改后的主要部分。
_RESET_ADDR = 0xBFC00000;
_BEV_EXCPT_ADDR = 0xBFC00380;
_DBG_EXCPT_ADDR = 0xBFC00480;
_SIMPLE_TLB_REFILL_EXCPT_ADDR = _ebase_address + 0;
_CACHE_ERR_EXCPT_ADDR = _ebase_address + 0x100;
_GEN_EXCPT_ADDR = _ebase_address + 0x180; /*************************************************************************
* Memory Regions
*
* Memory regions without attributes cannot be used for orphaned sections.
* Only sections specifically assigned to these regions can be allocated
* into these regions.
*
* The Debug exception vector is located at 0x9FC00480.
*
* The config_<address> sections are used to locate the config words at
* their absolute addresses.
*************************************************************************/
MEMORY
{
/* Bootloader user code: Only in the Lower Boot Alias */
kseg0_program_mem (rx) : ORIGIN = 0x9FC02000, LENGTH = 0xDF00
/* Lower Boot Alias last(5th) page: Not used */
kseg0_lba_last_page (rx) : ORIGIN = 0x9FC10000, LENGTH = 0x4000
/* Interrupt Vector table */
kseg0_boot_mem : ORIGIN = 0x9FC01000, LENGTH = 0x1000
/* Reset and C Startup module */
kseg1_boot_mem : ORIGIN = 0xBFC00000, LENGTH = 0x480
/* Cache TLB Initialization Table */
kseg1_boot_mem_4B0 : ORIGIN = 0xBFC004B0, LENGTH = 0xB50
BOOTLOADER MAIN CODE
修改后的linker script加到bootloader的项目中后，接着是bootloader的coding，以下是bootloader code的主要部分
if (linereceived)
{
for (ix = 0; ix < incrbytes; ix++)
{
Uart_Putc(frameBuffer[ix]);
}
Uart_Putc('\n');
cksum = bcount = GetXbyte(frameBuffer[LEN_NIBBLE1_INDEX],frameBuffer[LEN_NIBBLE2_INDEX]);
SourceAddr.v[1] = GetXbyte(frameBuffer[ADDRH_NIBBLE1_INDEX],frameBuffer[ADDRH_NIBBLE2_INDEX]);
SourceAddr.v[0] = GetXbyte(frameBuffer[ADDRL_NIBBLE1_INDEX],frameBuffer[ADDRL_NIBBLE2_INDEX]);
rectype = GetXbyte(frameBuffer[TYPE_NIBBLE1_INDEX],frameBuffer[TYPE_NIBBLE2_INDEX]);
switch(rectype)
{
case LINEAR_ADDRESS:
SourceAddr.v[3] = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+1],frameBuffer[TYPE_NIBBLE2_INDEX+2]);
SourceAddr.v[2] = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+3],frameBuffer[TYPE_NIBBLE2_INDEX+4]);
Checksum();
break;
case DATA:
if ((SourceAddr.word.HW == 0x1fc0)) break;
if (SourceAddr.Val >= (EraseAddr.Val+ PAGE_SIZE))
{
EraseAddr.Val = (SourceAddr.Val/PAGE_SIZE) * PAGE_SIZE;
NVMErasePage(EraseAddr.Val);
}
linereceived = 0;
for (ix=0; ix < 2*bcount;)
{
pData.byte.LB = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+0],frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+1]);
pData.byte.HB = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+2],frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+3]);
pData.byte.UB = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+4],frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+5]);
pData.byte.MB = GetXbyte(frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+6],frameBuffer[TYPE_NIBBLE2_INDEX+1+ix+7]);
unsigned int error = NVMWriteWord(SourceAddr.Val, pData.Val);
if ((error & 0x3000) > 0) Uart_Putc('N'); // for debug
error = 0;
SourceAddr.Val += 4;
ix += 8;
if (linereceived) Uart_Putc('X'); // for debug
}
Checksum();
//Buf_Init();
break;
case END:
Checksum();
U1MODE = 0x0;
U1STA = 0x0;
TRISCSET = 0x2000; /* RC13 Input */
LATCCLR = 0x6000; /* Clear LATC */
IPC28CLR = 0x1F00; /* Clear IPC28 */
IEC3bits.U1RXIE = 0; /* Clear IEC3 */
(*((void(*)(void))USER_APP_RESET_ADDRESS))();
break;
}
linereceived = 0;
incrbytes = 0;
}
Bootloader编译成功后，使用programmer烧录到target, 然后拔掉programmer。并且以后再更新application再也不需要programmer了。
APPLICATION LINKER SCRIPT
Bootloader和appication同时放置在闪存存储器中，要两者都可以正常工作，就必修确保两者不能有overlap。所以application的放置需要避开bootloader，这样需要需改application 的linker script。 以下是修改后的主要部分。
_RESET_ADDR = 0x9D001000;
_SIMPLE_TLB_REFILL_EXCPT_ADDR = _ebase_address + 0;
_CACHE_ERR_EXCPT_ADDR = _ebase_address + 0x100;
_GEN_EXCPT_ADDR = _ebase_address + 0x180; /*************************************************************************
* Memory Regions
*
* Memory regions without attributes cannot be used for orphaned sections.
* Only sections specifically assigned to these regions can be allocated
* into these regions.
*
* The Debug exception vector is located at 0x9FC00480.
* The config_<address> sections are used to locate the config words at
* their absolute addresses.
*************************************************************************/
MEMORY
{
kseg1_boot_mem : ORIGIN = 0x9D001000, LENGTH = 0x480
kseg0_program_mem (rx) : ORIGIN = 0x9D000000 + 0x1000 + 0x480, LENGTH = 0x200000 - (0x1000 + 0x480) /* All C files will be located here */ kseg0_boot_mem : ORIGIN = 0x9D000000, LENGTH = 0x0
kseg0_data_mem (w!x) : ORIGIN = 0x80000000, LENGTH = 0x80000
sfrs : ORIGIN = 0xBF800000, LENGTH = 0x100000
kseg2_ebi_data_mem : ORIGIN = 0xC0000000, LENGTH = 0x4000000
kseg2_sqi_data_mem : ORIGIN = 0xD0000000, LENGTH = 0x4000000
kseg3_ebi_data_mem : ORIGIN = 0xE0000000, LENGTH = 0x4000000
kseg3_sqi_data_mem : ORIGIN = 0xF0000000, LENGTH = 0x4000000
}
HOW TO USE HYPERBOOTLOADER_PIC32
1. 使用XC32编译HyperBootloader_PIC32（编译前，需先修改linker script）。
2. 使用pickit3烧录HyperBootloader_PIC32的Hex文件到目标板中。
3. 拔除pickit3烧录器，连接目标板与PC的串口，打开超级终端，设置如下：115200-8-None-1-None, Line Delay-20ms。
4. 重启目标板，超级终端会出现Booting... 字样。
5. 6秒内，打开Send Text File对话框，选择期望烧录的application的hex文件（编译前，需先修改linker script），点击确认， HyperBootloader会将接收到的数据传回到电脑超级终端上，并将数据烧录到目标板程序存储器的正确位置。
6. 烧录完毕，自动跳转去执行application。
之后每次更新application，只需重复步骤 4 ~ 6 就可以了。
NOTE
HyperBootloader不支持configuration bits的烧写，需要application的configuration bits 和HyperBootloader_PIC32的configuration bits保持一致。