玩儿转物联网IoT - 在Beagle Bone Black上运行node.js 程序

2022-12-29 07:20:22

物联网（IoT)技术方兴未艾，智能手环，智能血压计，智能眼镜甚至智能鞋垫都开始进入我们的生活，各种智能设备层出不穷，世界已经到了一个“人有多大胆，地有多大产”的时代，不玩儿点物联网都不好意思和人打招呼了。

之前玩儿过开源硬件Arduino，这次再找个功能强劲的Beagle Bone Black（BBB）。大家可能知道名气更大的树莓派，BBB也是类似的单片计算机开发板，就在名片大小的一块板子上集成了计算机的大多数常见功能，在上面可以运行Linix 操作系统，通过HDMI连上显示器，插上USB鼠标键盘就是一台完整计算机了。此外还可以配备一些外设Cape,比如触摸屏、音频扩展、串口扩展板等等。

如果你感兴趣，我大淘宝应该都可以买得到，我这边没有视频线，只能通过SSH连接到上面了。开箱后通过数据线连接到电脑上，如果板子没问题的话，靠近网卡口的小LED灯会闪烁。从右到左一次编号为USR0~3. USR 0 是心跳频率的闪烁，USR 2闪烁表示CPU活动。其他两个 USR1 当访问SD卡时闪烁，我没有安装SD卡，所以也不会亮。USR 3当访问 eMMC时闪烁。

设置 Beagle Bone Black

首先在本机上安装相关驱动，下面是驱动列表，我用的是Macbook Pro，安装下表中下载安装Max OS X对应的那两个就行了，安装很快，需要重启一下。

Operating System	USB Drivers	Comments
Windows (64-bit)	64-bit installer	If in doubt, try the 64-bit installer first. Note #1: Windows Driver Certification warning may pop up two or three times. Click “Ignore”, “Install” or “Run” Note #2: To check if you're running 32 or 64-bit Windows see this: https://support.microsoft.com/kb/827218. Note #3: On systems without the latest service release, you may get an error (0xc000007b). In that case, please install the following and retry: https://www.microsoft.com/en-us/download/confirmation.aspx?id=13523. Note #4: You may need to reboot Windows. Note #5: These drivers have been tested to work up to Windows 10
Windows (32-bit)	32-bit installer
Mac OS X	Network Serial	Install both sets of drivers.
Linux	mkudevrule.sh	Driver installation isn't required, but you might find a few udev rules helpful.

驱动安装完毕并重启机器后，就可以通过浏览器链接到BBB了。 BBB已经内置了Linux操作系统并且安装了Node.JS，还提供了BoneScript库，所以我们可以直接用Javascript来操纵硬件。JavaScript还能干这事？是的，我们可以打开Chrome浏览器（IE不行的），打开地址 http://192.168.7.2, 就会进入到运行在BBB上的网站，其中介绍了BoneScript，也有简单的例子直接可以运行，立刻就可以体验通过JavaScript来实现前面提到的LED灯的开关等实例。

为Beagle Bone Black启动WIFI

下面我想在BBB上运行一个我自己的node.js程序，一般都需要下载一些npm包，所以需要先让BBB连接互联网。BBB上已经带了网卡接口，不过插网线还是有些麻烦，用WIFI应该会更方便些。要放BBB访问WIFI需要一个小硬件，我手头刚好有一个，就是前些年炒的很火的360随身WIFI，上图中BBB上插的那个白色的就是。哈哈，想不到这东西当钥匙链当摆设很多年，今天排上了用场。

BBB的系统默认没没有启用WIFI功能，需要SSH登录上去更改一下。首先在Mac 的终端窗口中通过SSH登录到BBB。 BBB的IP地址的192.168.7.2, 其中默认安装了Debian Linux系统，用户名和密码是 debian/temppwd

Restored session: Wed Mar 9 15:13:18 CST 2016

daniels-MacBook-Pro:webglbim danieldu$ ssh debian@192.168.7.2

The authenticity of host '192.168.7.2 (192.168.7.2)' can't be established.

ECDSA key fingerprint is SHA256:426KRGxj0OmPAef1WAl/7nVaM26q6HXd1OM6mXJA9mw.

Are you sure you want to continue connecting (yes/no)? yes

Warning: Permanently added '192.168.7.2' (ECDSA) to the list of known hosts.

Debian GNU/Linux 7

BeagleBoard.org Debian Image 2015-03-01

Support/FAQ: http://elinux.org/Beagleboard:BeagleBoneBlack_Debian

default username:password is [debian:temppwd]

debian@192.168.7.2's password:

debian@beaglebone:~$

查看网络接口，并没有WIFI：

debian@beaglebone:~$ ip -4 a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN

inet 127.0.0.1/8 scope host lo

3: usb0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000

inet 192.168.7.2/30 brd 192.168.7.3 scope global usb0

那需要编辑 /etc/network/interface 文件, 如WIFI Example中写的那样，把前面的注释去掉，填写我家的WIFI SSID和密码，Ctrl+O保持后Ctrl+X退出。

debian@beaglebone:~$ sudo nano /etc/network/interfaces

# WiFi Example

auto wlan0

iface wlan0 inet dhcp

wpa-ssid “242”

wpa-psk “pwdpwd”

然后重启服务后再看一下，WIFI已经启用了

debian@beaglebone:~$ sudo /etc/init.d/networking restart

[ ok ] Restarting networking (via systemctl): networking.service.

debian@beaglebone:~$ ip -4 a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN

inet 127.0.0.1/8 scope host lo

3: usb0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000

inet 192.168.7.2/30 brd 192.168.7.3 scope global usb0

6: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000

inet 192.168.0.17/24 brd 192.168.0.255 scope global wlan0

测试一下，看看baidu能不能通，哈哈，果然可以上网了：）

debian@beaglebone:~$ wget http://www.baidu.com

2016-03-09 07:47:14 http://www.baidu.com/

Resolving www.baidu.com (www.baidu.com)… 14.215.177.38, 14.215.177.37

Connecting to www.baidu.com (www.baidu.com)|14.215.177.38|:80… connected.

HTTP request sent, awaiting response… 200 OK

Length: unspecified [text/html]

Saving to: `index.html'

[ <=> ] 98,181 1.67K/s in 11s

2016-03-09 07:47:26 (8.92 KB/s) - `index.html' saved [98181]

运行node.js 程序

下来可以在创建一个简单的node.js 应用程序，让它运行在BBB上。BBB上默认的node.js版本是0.10

debian@beaglebone:~$ node —version

v0.10.29

debian@beaglebone:~$ npm —version

1.4.21

下面先创建一个最简单的node.js程序试试看：

debian@beaglebone:~$ mkdir helloBBB

debian@beaglebone:~$ cd helloBBB/

debian@beaglebone:~/helloBBB$ npm init

This utility will walk you through creating a package.json file.

It only covers the most common items, and tries to guess sane defaults.

See `npm help json` for definitive documentation on these fields

and exactly what they do.

Use `npm install <pkg> —save` afterwards to install a package and

save it as a dependency in the package.json file.

Press ^C at any time to quit.

name: (helloBBB)

version: (0.0.0)

description: simple node.js app

entry point: (index.js)

test command:

git repository:

keywords:

author: Daniel Du

license: (ISC) MIT

About to write to /home/debian/helloBBB/package.json:

{

“name”: “helloBBB”,

“version”: “0.0.0”,

“description”: “simple node.js app “,

“main”: “index.js”,

“dependencies”: {

“express”: “^4.13.4”

“devDependencies”: {},

“scripts”: {

“test”: “echo "Error: no test specified" && exit 1”

“author”: “Daniel Du”,

“license”: “MIT”

}

Is this ok? (yes)

debian@beaglebone:~/helloBBB$ ls

node_modules package.json

debian@beaglebone:~/helloBBB$ nano index.js

用nano 编辑器创建index.js, 文件，建立一个最简单的express web应用。为了防止冲突，我把端口改成了8000：

var express = require('express');

var app = express();

app.get('/', function (req, res) {

  res.send('Hello World! This node.js application running from Beagle Bone Black!');

});

app.listen(8000, function () {

  console.log('Example app listening on port 8000!');

});

然后运行它：

debian@beaglebone:~/helloBBB$ ls

index.js node_modules package.son

debian@beaglebone:~/helloBBB$ npm install

debian@beaglebone:~/helloBBB$ node index.js

回到Mac上，打开浏览器，输入 http://192.168.7.2:8000, 哈哈, 成功！第一个简单的node.js 程序就在BBB上跑起来了。

码农公寓

相关文章