‘dmesg’命令显示linux内核的环形缓冲区信息，我们可以从中获得诸如系统架构、cpu、挂载的硬件，RAM等多个运行级别的大量的系统信息。当计算机启动时，系统内核（操作系统的核心部分）将会被加载到内存中。在加载的过程中会显示很多的信息，在这些信息中我们可以看到内核检测硬件设备。
dmesg Command Examples
dmesg 命令的使用范例
‘dmesg’命令设备故障的诊断是非常重要的。在‘dmesg’命令的帮助下进行硬件的连接或断开连接操作时，我们可以看到硬件的检测或者断开连接的信息。‘dmesg’命令在多数基于Linux和Unix的操作系统中都可以使用。
下面我们展示一些最负盛名的‘dmesg’命令工具以及其实际使用举例。‘dmesg’命令的使用语法如下。
# dmesg [options...]
1. 列出加载到内核中的所有驱动
我们可以使用如‘more’。 ‘tail’, ‘less ’或者‘grep’文字处理工具来处理‘dmesg’命令的输出。由于dmesg日志的输出不适合在一页中完全显示，因此我们使用管道（pipe）将其输出送到more或者less命令单页显示。
[root@tecmint.com ~]# dmesg | more
[root@tecmint.com ~]# dmesg | less
输出
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.--generic (buildd@aatxe) (gcc version 4.8. (Ubuntu/Linaro 4.8.-10ubuntu8) ) #-Ubuntu SMP Wed Oct :: UTC
(Ubuntu 3.11.-13.20-generic 3.11.)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007dc08bff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007dc08c00-0x000000007dc5cbff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007dc5cc00-0x000000007dc5ebff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007dc5ec00-0x000000007fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fed003ff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fed9ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000feefffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[ 0.000000] NX (Execute Disable) protection: active
.....
2. 列出所有被检测到的硬件
要显示所有被内核检测到的硬盘设备，你可以使用‘grep’命令搜索‘sda’关键词，如下：
[root@tecmint.com ~]# dmesg | grep sda [ 1.280971] sd :::: [sda] -byte logical blocks: ( GB/ GiB)
[ 1.281014] sd :::: [sda] Write Protect is off
[ 1.281016] sd :::: [sda] Mode Sense: 3a
[ 1.281039] sd :::: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.359585] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 1.360052] sd :::: [sda] Attached SCSI disk
[ 2.347887] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 22.928440] Adding 3905532k swap on /dev/sda6. Priority:- extents: across:3905532k FS
[ 23.950543] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ 24.134016] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
[ 24.330762] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 24.561015] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
注解 ‘sda’表示第一块 SATA硬盘，‘sdb’表示第二块SATA硬盘。若想查看IDE硬盘搜索‘hda’或‘hdb’关键词。
3. 只输出dmesg命令的前20行日志
在‘dmesg’命令后跟随‘head’命令来显示开始几行，‘dmesg | head -20′命令将显示开始的前20行。
[root@tecmint.com ~]# dmesg | head - [ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.--generic (buildd@aatxe) (gcc version 4.8. (Ubuntu/Linaro 4.8.-10ubuntu8) ) #-Ubuntu SMP Wed Oct :: UTC (Ubuntu 3.11.-13.20-generic 3.11.)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007dc08bff] usable
[ 0.000000] BIOS-e820: [mem 0x000000007dc08c00-0x000000007dc5cbff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000007dc5cc00-0x000000007dc5ebff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000007dc5ec00-0x000000007fffffff] reserved
4. 只输出dmesg命令最后20行日志
在‘dmesg’命令后跟随‘tail’命令（‘ dmesg | tail -20’）来输出‘dmesg’命令的最后20行日志，当你插入可移动设备时它是非常有用的。
[root@tecmint.com ~]# dmesg | tail - parport0: PC-style at 0x378, irq [PCSPP,TRISTATE]
ppdev: user-space parallel port driver
EXT4-fs (sda1): mounted filesystem with ordered data mode
Adding 2097144k swap on /dev/sda2. Priority:- extents: across:2097144k
readahead-disable-service: delaying service auditd
ip_tables: (C) - Netfilter Core Team
nf_conntrack version 0.5. ( buckets, max)
NET: Registered protocol family
lo: Disabled Privacy Extensions
e1000: eth0 NIC Link is Up Mbps Full Duplex, Flow Control: None
Slow work thread pool: Starting up
Slow work thread pool: Ready
FS-Cache: Loaded
CacheFiles: Loaded
CacheFiles: Security denies permission to nominate security context: error -
eth0: no IPv6 routers present
type= audit(1398268784.593:): audit_enabled= old= auid= ses= res=
readahead-collector: starting delayed service auditd
readahead-collector: sorting
readahead-collector: finished
5. 搜索包含特定字符串的被检测到的硬件
由于‘dmesg’命令的输出实在太长了，在其中搜索某个特定的字符串是非常困难的。因此，有必要过滤出一些包含‘usb’ ‘dma’ ‘tty’ ‘memory’等字符串的日志行。grep 命令 的‘-i’选项表示忽略大小写。
[root@tecmint.com log]# dmesg | grep -i usb
[root@tecmint.com log]# dmesg | grep -i dma
[root@tecmint.com log]# dmesg | grep -i tty
[root@tecmint.com log]# dmesg | grep -i memory
输出
[ 0.000000] Scanning areas for low memory corruption
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] init_memory_mapping: [mem 0x37800000-0x379fffff]
[ 0.000000] init_memory_mapping: [mem 0x34000000-0x377fffff]
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x33ffffff]
[ 0.000000] init_memory_mapping: [mem 0x37a00000-0x37bfdfff]
[ 0.000000] Early memory node ranges
[ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x000effff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2003288K/2059928K available (6352K kernel code, 607K rwdata, 2640K rodata, 880K init, 908K bss, 56640K reserved, 1146920K highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.004291] Initializing cgroup subsys memory
[ 0.004609] Freeing SMP alternatives memory: 28K (c1a3e000 - c1a45000)
[ 0.899622] Freeing initrd memory: 23616K (f51d0000 - f68e0000)
[ 0.899813] Scanning for low memory corruption every seconds
[ 0.946323] agpgart-intel ::00.0: detected 32768K stolen memory
[ 1.360318] Freeing unused kernel memory: 880K (c1962000 - c1a3e000)
[ 1.429066] [drm] Memory usable by graphics device = 2048M
6. 清空dmesg缓冲区日志
我们可以使用如下命令来清空dmesg的日志。该命令会清空dmesg环形缓冲区中的日志。但是你依然可以查看存储在‘/var/log/dmesg’文件中的日志。你连接任何的设备都会产生dmesg日志输出。
[root@tecmint.com log]# dmesg -c
7. 实时监控dmesg日志输出
在某些发行版中可以使用命令‘tail -f /var/log/dmesg’来实时监控dmesg的日志输出。
[root@tecmint.com log]# watch "dmesg | tail -20"
结论：dmesg命令在系统dmesg记录实时更改或产生的情况下是非常有用的。你可以使用man dmesg来获取更多关于dmesg的信息。