Centos 6.5 搭建l2tp 服务端和客户端

2022-10-21 11:37:00

废话不多说直接上步骤。

server

#epel仓库愿安装

rpm -ivh http://mirrors.ustc.edu.cn/fedora/epel/6/x86_64/epel-release-6-8.noarch.rpm

#l2tp程序安装

yum install openswan ppp xl2tpd -y

vim /etc/ipsec.conf

config setup

    nat_traversal=yes

    virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12

    oe=off

    protostack=netkey

conn L2TP-PSK-NAT

    rightsubnet=vhost:%priv

    also=L2TP-PSK-noNAT

conn L2TP-PSK-noNAT

    authby=secret

    pfs=no

    auto=add

    keyingtries=3

    rekey=no

    ikelifetime=8h

    keylife=1h

    type=transport

    left=192.168.42.191        #换成自己的公网ip，由于我这里测试所以是内网

    leftprotoport=17/1701

    right=%any

    rightprotoport=17/%any

vim /etc/ipsec.secrets

192.168.42.191 %any: PSK "shiyiwen"       #修改ip 和 密码

把如下添加进 /etc/sysctl.conf         #注意顺序

    net.ipv4.ip_forward = 1

    net.ipv4.conf.default.rp_filter = 0

    net.ipv4.conf.all.send_redirects = 0

    net.ipv4.conf.default.send_redirects = 0

    net.ipv4.conf.all.log_martians = 0

    net.ipv4.conf.default.log_martians = 0

    net.ipv4.conf.default.accept_source_route = 0

    net.ipv4.conf.all.accept_redirects = 0

    net.ipv4.conf.default.accept_redirects = 0

    net.ipv4.icmp_ignore_bogus_error_responses = 1

sysctl -p 刷新

启动ipsec 和xl2tpd 应用

ipsec restart

/etc/init.d/xl2tpd start

chkconfig xl2tpd on

chkconfig  ipsec on

使用ipsec verify查看状态 （关闭selinux 和iptables 如果要开iptables 本文下面有全的）

Centos 6.5 搭建l2tp 服务端和客户端

enabled 没有管，因为后面也可以连接成功，内核参数也是设置对的。有知道的通知望告诉我。

/etc/xl2tpd/xl2tpd.conf 这里的配置文件可以配置分配的网段还有一些其他参数。默认可以不配置。

接下来配置ppp协议

vim /etc/ppp/chap-secrets  #配置用户名和密码其实还有权限。

# Secrets for authentication using CHAP

# client        server  secret                  IP addresses

  admin * "yingzi" *

重启xl2tpd 服务

===============================================================

client：

#安装epel源

#安装客户端l2tpd 这里我们还是用xl2tpd，当然2边都需要ppp协议

yum install xl2tpd ppp

vim /etc/xl2tpd/xl2tpd.conf

[lac sywvpn]

name = admin;

lns = 192.168.42.191;

pppoptfile = /etc/ppp/peers/sywvpn.l2tpd;

ppp debug = yes;

vim /etc/ppp/peers/sywvpn.l2tpd

#下面对应的参数是服务端配置过的
remotename sywvpn

user "admin"

password "yingzi"

unit 0

lock

nodeflate

nobsdcomp

noauth

persist

nopcomp

noaccomp

debug

#启动客户端

/etc/init.d/xl2tpd start

# 启动还没开始拨号。

开始拨号

echo 'c sywvpn' > /var/run/xl2tpd/l2tp-control

# 查看client拨号日志

Aug 31 15:38:59 app7 xl2tpd[3464]: Connecting to host 192.168.42.191, port 1701

Aug 31 15:38:59 app7 xl2tpd[3464]: Connection established to 192.168.42.191, 1701.  Local: 52638, Remote: 44491 (ref=0/0).

Aug 31 15:38:59 app7 xl2tpd[3464]: Calling on tunnel 52638

Aug 31 15:38:59 app7 xl2tpd[3464]: Call established with 192.168.42.191, Local: 28263, Remote: 3204, Serial: 2 (ref=0/0)

Aug 31 15:38:59 app7 pppd[4629]: pppd 2.4.5 started by root, uid 0

Aug 31 15:38:59 app7 pppd[4629]: Using interface ppp0

Aug 31 15:38:59 app7 pppd[4629]: Connect: ppp0 <--> /dev/pts/2

Aug 31 15:39:02 app7 pppd[4629]: CHAP authentication succeeded: Access granted

Aug 31 15:39:02 app7 pppd[4629]: CHAP authentication succeeded

Aug 31 15:39:02 app7 pppd[4629]: local  IP address 192.168.1.128

Aug 31 15:39:02 app7 pppd[4629]: remote IP address 192.168.1.99

#查看server端日志

Aug 31 15:38:41 Monitor xl2tpd[30013]: control_finish: Connection closed to 172.16.38.7, port 1701 (Goodbye!), Local: 63296, Remote: 51768  #之前断的

Aug 31 15:38:59 Monitor xl2tpd[30013]: Connection established to 172.16.38.7, 1701.  Local: 44491, Remote: 52638 (ref=0/0).  LNS session is 'default'

Aug 31 15:38:59 Monitor xl2tpd[30013]: Call established with 172.16.38.7, Local: 3204, Remote: 28263, Serial: 2

Aug 31 15:38:59 Monitor pppd[30138]: pppd 2.4.5 started by root, uid 0

Aug 31 15:38:59 Monitor pppd[30138]: Using interface ppp0

Aug 31 15:38:59 Monitor pppd[30138]: Connect: ppp0 <--> /dev/pts/1

Aug 31 15:39:02 Monitor pppd[30138]: Cannot determine ethernet address for proxy ARP

Aug 31 15:39:02 Monitor pppd[30138]: local  IP address 192.168.1.99

Aug 31 15:39:02 Monitor pppd[30138]: remote IP address 192.168.1.128

#ifconfig 客户端

ppp0      Link encap:Point-to-Point Protocol

          inet addr:192.168.1.128  P-t-P:192.168.1.99  Mask:255.255.255.255

          UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1410  Metric:1

          RX packets:1341 errors:0 dropped:0 overruns:0 frame:0

          TX packets:1341 errors:0 dropped:0 overruns:0 carrier:0

          collisions:0 txqueuelen:3

          RX bytes:112434 (109.7 KiB)  TX bytes:112440 (109.8 KiB)

#ping 服务端

[root@app7 var]# ping 192.168.1.99

PING 192.168.1.99 (192.168.1.99) 56(84) bytes of data.

64 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=4.26 ms

64 bytes from 192.168.1.99: icmp_seq=2 ttl=64 time=4.01 ms

64 bytes from 192.168.1.99: icmp_seq=3 ttl=64 time=3.88 ms

64 bytes from 192.168.1.99: icmp_seq=4 ttl=64 time=3.91 ms

64 bytes from 192.168.1.99: icmp_seq=5 ttl=64 time=3.86 m

#断开拨号

echo 'd sywvpn' > /var/run/xl2tpd/l2tp-control

#查看该文件应该属于数据库过度文件

prw------- 1 root root 0 Aug 31 15:38 /var/run/xl2tpd/l2tp-control

# 网上解释如下

管道（FIFO，pipe）
用来解决多个程序同时访问一个文件所造成的错误问题，first-in-first-out(FIFO)，第一属性为（p）。
=================================================配置 iptables 来自网络======服务端的哦===========
 
 
iptables -t nat -A POSTROUTING -s 192.168.7.0/24 -o eth0 -j MASQUERADE
iptables -I FORWARD -s 192.168.7.0/24 -j ACCEPT
iptables -I FORWARD -d 192.168.7.0/24 -j ACCEPT
iptables-save
service iptables restart

192.168.7.0/24根据实际情况替换。

vi /etc/sysconfig/iptables 看到的应该是类似这样。
最上面先是nat规则，下面是filter规则。
下面filter表里，先把VPN要用到的udp端口1701，500，4500都打开。要用openvp的话，还要开1194。
另外filter表里，一定要有FORWARD规则。这点在网上好几个教程里都没说！坑死人。

Shell
#下面规则做参考啊，新手别完全照抄。
*nat
:PREROUTING ACCEPT [39:3503]
:POSTROUTING ACCEPT [0:0]
:OUTPUT ACCEPT [0:0]
-A POSTROUTING -s 192.168.7.0/24 -o eth0 -j MASQUERADE
COMMIT
# Completed on Thu Jun 28 15:50:40 2012
# Generated by iptables-save v1.4.7 on Thu Jun 28 15:50:40 2012
*filter
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [121:13264]
-A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -p icmp -j ACCEPT
-A INPUT -i lo -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 53 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 1194 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 1701 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 500 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 4500 -j ACCEPT-A INPUT -j REJECT --reject-with icmp-host-prohibited
-A FORWARD -d 192.168.7.0/24 -j ACCEPT
-A FORWARD -s 192.168.7.0/24 -j ACCEPT
-A FORWARD -j REJECT --reject-with icmp-host-prohibited
COMMIT
# Completed on Thu Jun 28 15:50:40 2012
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
#下面规则做参考啊，新手别完全照抄。
*nat
:PREROUTING ACCEPT [39:3503]
:POSTROUTING ACCEPT [0:0]
:OUTPUT ACCEPT [0:0]
-A POSTROUTING -s 192.168.7.0/24 -o eth0 -j MASQUERADE
COMMIT
# Completed on Thu Jun 28 15:50:40 2012
# Generated by iptables-save v1.4.7 on Thu Jun 28 15:50:40 2012
*filter
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [121:13264]
-A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -p icmp -j ACCEPT
-A INPUT -i lo -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 53 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 53 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 1194 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 1701 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 500 -j ACCEPT
-A INPUT -p udp -m state --state NEW -m udp --dport 4500 -j ACCEPT-A INPUT -j REJECT --reject-with icmp-host-prohibited
-A FORWARD -d 192.168.7.0/24 -j ACCEPT
-A FORWARD -s 192.168.7.0/24 -j ACCEPT
-A FORWARD -j REJECT --reject-with icmp-host-prohibited
COMMIT
# Completed on Thu Jun 28 15:50:40 2012

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　by:V

上一篇：easyui datagrid footer 页脚问题


下一篇：Ubuntu Server 配置网络