///
/// </param>
/// <returns></returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_CommOpenWithBaud", SetLastError = true, CharSet = CharSet.Ansi, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern IntPtr M100A_CommOpenWithBaud(string port, uint baudRate);
/// <summary>
/// 关闭当前打开的串口
/// </summary>
/// <param name="comHandle">要关闭的串口的句柄</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_CommClose", SetLastError = true, CharSet = CharSet.Ansi, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_CommClose(IntPtr comHandle);
/// <summary>
/// 设置 M100A 的通讯波特率
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="baud">波特率选项
/// =0x33, 设置波特率为9600
/// =0x34, 设置波特率为19200
/// =0x35, 设置波特率为38400
/// </param>
/// <param name="recrodInfo">存储该条命令的通讯记录
/// 格式如下: TX: 02 00 02 46 33 03 76
/// RX: 06
/// TX: 05
/// RX: 02 00 03 50 46 33 03 27
/// </param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_SetCommBaud", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_SetCommBaud(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte baud, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recrodInfo);
/// <summary>
/// M100A 复位命令
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="pm">
/// 复位选项
///=0x30,初始化读卡器,有卡弹卡(不上传版本信息)
///=0x31,初始化读卡器,有卡回收(不上传版本信息)
///=0x32,初始化读卡器,有卡停在读磁卡位置(不上传版本信息)
///=0x33,初始化读卡器,有卡停在读IC 卡位置(不上传版本信息)
///=0x34,初始化读卡器,不动作(上传版本信息)
/// </param>
/// <param name="verCode">存储的是机器的版本信息,如“TTCE_M100A_V*.**”</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_Reset", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_Reset(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte pm, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] verCode, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 读取卡片在机器里的位置
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="cardStates">CardStates[0],表示通道卡片位置,具体含义如下
///=0x30:通道无卡
///=0x31:读磁卡位置有卡
///=0x32:IC卡位置有卡
///=0x33:前端夹卡位置有卡
///=0x34:前端不夹卡位置有卡
///=0x35:卡不在标准位置(标准位置指的是上面5个位置
///(0x30~0x34).当卡不在标准位置时,可以通过移动卡片
///命令将卡移动到标准位置)
///=0x36:卡片正在移动中
///=0x37:射频卡位置有卡
///CardStates[1],表示卡箱卡片状态
///=0x30:卡箱无卡
///=0x31:卡箱卡片不足,提醒需要加卡
///=0x32:卡箱卡片足够</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_CheckCardPosition", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_CheckCardPosition(IntPtr comHandle, bool bHasMacAddr, byte macAddr, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] cardStates, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 读每个传感器的状态
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="sensorStates">9组传感器的状态值(各个传感器位置分步请查看演示程序)
///上传顺序:C_S1,C_S2,C_S3,C_S4,C_S5,C_S6,B_S1,B_S2,B_S3
///=0x30:无卡。
///=0x31:有卡。</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_CheckSensorStates", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_CheckSensorStates(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte[] sensorStates, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 读前6组传感器的电压
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="sensorVoltage">存储前6组传感器的电压信息,计算方法请参照通讯协议中“读取传
///感器电压”指令</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_CheckSensorVoltage", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_CheckSensorVoltage(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte[] sensorVoltage, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 进卡设置,为立即返回方式,卡片一旦进入,则命令失效,卡片是否到具体位置,必须通过“读
/// 取卡片在机器里的位置”命令来判断
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="enterType">具体有效值如下
///0x30: 禁止进卡(将取消先前设置好的进卡指令)
///0x31: 使能进卡,进卡后停卡在读磁卡位置
///0x32: 使能进卡,进卡后停卡在读IC卡位置
///0x33: 使能进卡,进卡后将卡回收到回收箱
///0x34: 使能进卡,进卡后停卡在前端夹卡位置
///0x35: 使能进卡,进卡后将卡弹出</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_EnterCard", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_EnterCard(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte enterType, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 卡片传动指令
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="pm">卡片传动的选项,有效值如下:
///0x30: 将卡片传动到读磁卡位置
///0x31: 将卡片传动到IC卡位置
///0x32: 将卡片传动到前端夹卡位置
///0x33: 将卡片弹出
///0x34: 将卡片回收到回收箱</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_MoveCard", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_MoveCard(IntPtr comHandle, bool bHasMacAddr, byte macAddr, byte pm, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
/// <summary>
/// 向机器发送EOT,取消命令
/// </summary>
/// <param name="comHandle">已经打开的串口的句柄</param>
/// <param name="bHasMacAddr">是否为多机通讯版本(使用方式请参文档前部“接口函数公有的参数说明“)</param>
/// <param name="macAddr">机器的地址,有效取值(0 到15)</param>
/// <param name="recordInfo">存储该条命令的通讯记录</param>
/// <returns>正确=0,错误=非0</returns>
[DllImport("M100A_DLL.dll", EntryPoint = "M100A_Eot", SetLastError = true, CharSet = CharSet.Auto, ExactSpelling = true, CallingConvention = CallingConvention.StdCall)]
public static extern int M100A_Eot(IntPtr comHandle, bool bHasMacAddr, byte macAddr, [Out, MarshalAs(UnmanagedType.LPArray)] byte[] recordInfo);
public static byte READ_CARD_LOCATION = 0x30;//将卡片传动到读磁卡位置
public static byte IC_CARD_LOCATION = 0x31;// 将卡片传动到IC卡位置
public static byte RECOVERBOX_CARD_LOCATION = 0x34;// 将卡片回收到回收箱
public static byte FRONTEND_CARD_LOCATION = 0x32;//将卡片传动到前端夹卡位置
public static byte POB_CARD = 0x33;//将卡片弹出
}
}
总结:这个”M100A_DLL.dll”文件要放在测试项目的根目录下,编译一下就能用了,注意一下!