LVS+Keepalived 高可用性负载均衡自动化配置

2022-04-06 08:36:45

前言* 随着互联网飞速的发展，互联网WEB服务器，必须要保证每天7x24x365不间断服务，随着人数不断的增加，有什么好的WEB前端架构呢？既能实现高可用、负载均衡、成本有最低廉呢？答案有木有呢？LVS+Keepalived是一个非常不错的前端均衡选择。（今天来研究一下如何快速配置LVS及日常的维护，供参考！）

一、系统环境

LVS-Master 192.168.2.108

LVS-BACKUP 192.168.2.109

LVS-DR-VIP 192.168.2.100

WEB1-Realserver 192.168.2.79

WEB2-Realserver 192.168.2.80

二、Keepalived安装

由于我们使用的是lvs+keepalived，所以这里不需要配置lvs-dr脚本，直接在keepalived.conf里面配置即可！

#!/bin/sh
###脚本编写目的:自动安装lvs+keepalived

###编写时间: 2011年7月6日17:25:39
###初稿人:wugk
###定义变量
DIR1=/usr/src
DIR2=/usr/local
cat << EOF
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

++++Welcome to use Linux installed a key LVS+KEEPALIVED shells scripts
+++++++++++++++++++++*************************++++++++++++++++++++++++
EOF
if

[ $UID -ne 0 ];then

echo “This script must use root user ,please exit……”

sleep 2

exit 0
fi
download ()
{

cd $DIR1 && wget -c http://www.linuxvirtualserver.org/software/kernel-2.6/ipvsadm-1.24.tar.gz http://www.keepalived.org/software/keepalived-1.1.15.tar.gz
if

[ $? = 0 ];then

echo "Download LVS Code is OK!"
else

echo "Download LVS Code is failed,Please check!"

exit 1
fi
}
ipvsadm_install ()
{

ln -s $DIR1/kernels/2.6.* $DIR1/linux

cd $DIR1 && tar xzvf ipvsadm-1.24.tar.gz &&cd ipvsadm-1.24 && make && make install
if

[ $? -eq 0 ];then

echo "Install ipvsadm success,please waiting install keepalived ..............."
else

echo "Install ipvsadm failed ,please check !"

exit 1
fi
}
keepalived_install ()
{

cd $DIR1 && tar -xzvf keepalived-1.1.15.tar.gz &&cd keepalived-1.1.15 && ./configure && make && make install
if

[ $? -eq 0 ];then

echo "Install keepalived success,please waiting configure keepalived ..............."
else

echo "Install keepalived failed ,please check install version !"

exit 1
fi
}
######如果以上软件包编译报错的话，请检查相关的版本跟系统版本之间的关系，然后手动下载安装.
keepalived_config ()
{
cp $DIR2/etc/rc.d/init.d/keepalived /etc/rc.d/init.d/ && cp $DIR2/etc/sysconfig/keepalived /etc/sysconfig/ && mkdir -p /etc/keepalived &&cp $DIR2/etc/keepalived/keepalived.conf /etc/keepalived/ && cp $DIR2/sbin/keepalived /usr/sbin/
if

[ $? -eq 0 ];then

echo "Keepalived system server config success!"
else

echo "Keepalived system server config failed ,please check keepalived!"

exit 1
fi
}

PS3="Please select Install Linux Packages:"

select option in download ipvsadm_install keepalived_install keepalived_config
do
$option
done

以上脚本分别在lvs-master和lvs-backup上执行安装。

三、Keepalived配置

也可以参考配置：http://chinaapp.sinaapp.com/download/keepalived.conf 可以直接打开

! Configuration Filefor keepalived
global_defs {

  notification_email {

   wgkgood@163.com

  }

  notification_email_from wgkgood@163.com

  smtp_server 127.0.0.1

  smtp_connect_timeout 30

  router_id LVS_DEVEL
}
# VIP1
vrrp_instance VI_1 {

  state MASTER

  interface eth0

  lvs_sync_daemon_inteface eth0

  virtual_router_id 51

  priority 100

  advert_int 5

  authentication {

    auth_type PASS

    auth_pass 1111

  }

  virtual_ipaddress {

    192.168.2.100

  }
}
#REAL_SERVER_1

virtual_server 192.168.2.100 80 {

  delay_loop 6

  lb_algo wlc

  lb_kind DR

  persistence_timeout 60

  protocol TCP

  real_server 192.168.2.79 80 {

    weight 100

    TCP_CHECK {

    connect_timeout 10

    nb_get_retry 3

    delay_before_retry 3

    connect_port 80

    }
}
#REAL_SERVER_2

  real_server 192.168.2.80 80 {

    weight 100

    TCP_CHECK {

    connect_timeout 10

    nb_get_retry 3

    delay_before_retry 3

    connect_port 80

    }

  }
}

注意***Lvs-backup端同样配置，只需要更改state MASTER为state BACKUP，修改priority 100为priority 90即可。

四、WEB服务端配置

如下的VIP1指的是lvs-dr-vip地址，及对外提供访问的虚拟ip：

#!/bin/sh

PS3="Please Choose whether or not to start a realserver VIP1 configuration:"

select i in"start""stop"
do

case"$i"in
start)

read -p "Please enter the virtual server IP address:" VIP1

ifconfig lo:0 $VIP1 netmask 255.255.255.255 broadcast $VIP1

/sbin/route add -host $VIP1 dev lo:0

echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore

echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce

echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore

echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce

sysctl -p >/dev/null 2>&1

echo "RealServer Start OK"

exit 0
;;
stop)

ifconfig lo:0 down

route del $VIP1 >/dev/null 2>&1

echo "0" >/proc/sys/net/ipv4/conf/lo/arp_ignore

echo "0" >/proc/sys/net/ipv4/conf/lo/arp_announce

echo "0" >/proc/sys/net/ipv4/conf/all/arp_ignore

echo "0" >/proc/sys/net/ipv4/conf/all/arp_announce

echo "RealServer Stoped"

exit 1
;;
*)

echo "Usage: $0 {start|stop}"

exit 2
esac
done

脚本会提示是否启动，按1即启动，然后输入vip地址 192.168.2.100 ，用ifconfig你会看到：lo:0的ip即表示配置ip成功。

lo:0  Link encap:Local Loopback

   inet addr:192.168.2.100 Mask:255.255.255.255

   UP LOOPBACK RUNNING MTU:16436 Metric:1

五、测试LVS+keepalived

/etc/init.d/keepalived restart 查看lvs-master日志：

在浏览器里面访问 http://192.168.2.100/ 即可！当你宕掉lvs-master后，lvs-backup会接管变成lvs-master提供服务，当lvs-master故障恢复后，lvs-backup又会变成原来的状态！
所安装的脚本可以在这里下载：

在lvs-master和lvs-backup上执行http://chinaapp.sinaapp.com/download/lvs-keepalived.sh

在web服务器端执行http://chinaapp.sinaapp.com/download/realserver.sh

六、实战建议

为了解决脑裂问题，需要把主MASTER和备BACKUP各自的keepalived.conf配置文件里面的state 状态都改成BACKUP，优先级分别设置100和90。
我们常听说脑裂问题，到底什么是脑裂问题呢？
在集群配置中的split-brain现象是指，主从之间互相检测不到心跳，同时抢占资源，导致
服务无法正常访问的情况。所以我们还需要在主备keepalived.conf添加nopreempt 指令！

附realserver.sh脚本文件：

本文转自 wgkgood 51CTO博客，原文链接:http://blog.51cto.com/wgkgood/605322

码农公寓

相关文章