这个问题困扰了好几天，今天终于在大谷歌的帮助下，在这个网站http://blog.bwysystems.com/bwysystems/?p=16上找到了答案！还是国外的技术论坛强，在百度上搜遍了也没有找到这篇文章，下面简单叙述整个安装过程。
1. 安装e1000e驱动。
1. Move the base driver tar file to the directory of your choice. For
example, use /home/username/e1000e or /usr/local/src/e1000e. 2. Untar/unzip archive: tar zxf e1000e-x.x.x.tar.gz 3. Change to the driver src directory: cd e1000e-x.x.x/src/ 4. Compile the driver module: # make install The binary will be installed as: /lib/modules/<KERNEL VERSION>/kernel/drivers/net/e1000e/e1000e.[k]o The install locations listed above are the default locations. They
might not be correct for certain Linux distributions. 5. Load the module using either the insmod or modprobe command: modprobe e1000e insmod e1000e Note that for 2.6 kernels the insmod command can be used if the full
path to the driver module is specified. For example: insmod /lib/modules/<KERNEL VERSION>/kernel/drivers/net/e1000e/e1000e.ko With 2.6 based kernels also make sure that older e1000e drivers are
removed from the kernel, before loading the new module: rmmod e1000e; modprobe e1000e 6. Assign an IP address to the interface by entering the following, where
x is the interface number: ifconfig ethx <IP_address> 7. Verify that the interface works. Enter the following, where <IP_address>
is the IP address for another machine on the same subnet as the
interface that is being tested: ping <IP_address>
2. 安装igb驱动。如果没有这一步，ifconfig -a是看不到eth2..eth5接口的，通过lspci可以看到下面的信息：
03:00.0 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
03:00.1 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
04:00.0 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
04:00.1 Ethernet controller: Intel Corporation Device 10c9 (rev 01)
06:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
07:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
在这个网址http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=13663&lang=eng下载igb文件，然后安装下面步骤安装：
# tar xfv igb-1.2.44.9.tar.gz
# cd igb-1.2.44.9/src
# make
# make install
# modprobe igb
3. 使用ifconfig -a可以看到如下信息(下面是IP配置好的结果)
[root@localhost src]# ifconfig
eth0 Link encap:Ethernet HWaddr :::B3::
inet addr:192.168.115.178 Bcast:192.168.115.255 Mask:255.255.255.0
inet6 addr: fe80:::48ff:feb3:/ Scope:Link
UP BROADCAST RUNNING MULTICAST MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (3.6 GiB) TX bytes: (1.9 MiB)
Interrupt: eth2 Link encap:Ethernet HWaddr :E0:ED::8B:AE
inet addr:192.168.115.60 Bcast:192.168.115.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:edff:fe21:8bae/ Scope:Link
UP BROADCAST RUNNING MULTICAST MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (862.1 MiB) TX bytes: (1.3 KiB) eth3 Link encap:Ethernet HWaddr :E0:ED::8B:AF
inet addr:192.168.115.61 Bcast:192.168.115.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:edff:fe21:8baf/ Scope:Link
UP BROADCAST RUNNING MULTICAST MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (859.9 MiB) TX bytes: (1.4 KiB) eth4 Link encap:Ethernet HWaddr :E0:ED::8B:B0
inet addr:192.168.115.62 Bcast:192.168.115.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:edff:fe21:8bb0/ Scope:Link
UP BROADCAST RUNNING MULTICAST MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (864.3 MiB) TX bytes: (1.4 KiB) eth5 Link encap:Ethernet HWaddr :E0:ED::8B:B1
inet addr:192.168.115.63 Bcast:192.168.115.255 Mask:255.255.255.0
inet6 addr: fe80::2e0:edff:fe21:8bb1/ Scope:Link
UP BROADCAST RUNNING MULTICAST MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (836.5 MiB) TX bytes: (1.3 KiB) lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::/ Scope:Host
UP LOOPBACK RUNNING MTU: Metric:
RX packets: errors: dropped: overruns: frame:
TX packets: errors: dropped: overruns: carrier:
collisions: txqueuelen:
RX bytes: (8.1 MiB) TX bytes: (8.1 MiB) [root@localhost src]#
http://blog.bwysystems.com/bwysystems/?p=16网站的内容如下：
Linux Intel PRO/ GB Ethernet Controller
Back to the server that was sitting on my desk… The Debian Lenny installation did not seem to recognize the Intel Pro/ // server Ethernet cards, dual port, PCI-E x4. I ran: # lspci | grep Ethernet to list the pci devices (duh ). This gave me the following output: :00.0 Ethernet controller: Intel Corporation Device 10c9 (rev )
:00.1 Ethernet controller: Intel Corporation Device 10c9 (rev )
:00.0 Ethernet controller: Intel Corporation Device 10c9 (rev )
:00.1 Ethernet controller: Intel Corporation Device 10c9 (rev )
:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection
:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection The last two are the on board Ethernet controllers that work fine using the e1000e driver. The ones that I really wanted working were the first items displayed as “Device 10c9 (rev )”. I couldn’t find anything on the internet other than a German post, which looked like the guy was having the same problem (I can’t decipher German). So I started trying out some different Intel drivers. I first tried the standard e1000 driver as I noticed even some PCI express cards used this driver. That didn’t work. Then on my second shot I tried out this one “igb-1.2.44.9.tar.gz”. I’m assuming “igb” stands for Intel Gigabit, which makes sense as that’s what those cards are. If you don’t have the Intel driver disc that came with your cards you can find this driver here: http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=13663&lang=eng To install this driver just do the following: # tar xfv igb-1.2.44.9.tar.gz
# cd igb-1.2.44.9/src
# make
# make install
# modprobe igb As soon as I executed “modprobe igb” I instantly had new eth interfaces! You might want to add “igb” to /etc/modules, which is where you can also supply some parameters for the driver. Hopefully this post will help out anyone else who is having trouble with these cards on Debian. This entry was posted on Sunday, November 15th, at : pm and is filed under Debian GNU/Linux. You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.
Responses to “Linux Intel PRO/ GB Ethernet Controller”