case语句格式
# vi test.sh : echo "input : " read num echo "the input data is $num" case $num in 1) echo "January";; 双分号结束 2) echo "Feburary";; 5) echo "may" 每个case可以有多条命令 echo "sdfd" echo "sdf";; 但最后一条命令一定是双分号结束 *) echo "not correct input";; *)是其他值、default的意思 esac |
# sh ./test.sh input : 2 the input data is 2 Feburary # sh ./test.sh input : ter the input data is ter not correct input |
case 语句如果某个选项没有任何语句,也要加;; 否则会出下边错误
test: line 166: syntax error near unexpected
token `)'
test: line 166: `"system hostname config")'
匹配符[]是专门针对单字符的值,如果用[no],就是n和o之一
case $yn in [no]) return 1;; * ) echo "only accept Y,y,N,n,YES,yes,NO,no" >&2;; |
[macg@mac-home ~]$ sh test.sh enter y/n : no only accept Y,y,N,n,YES,yes,NO,no |
改正
case $yn in no) return 1;; NO) return 1;; * ) echo "only accept Y,y,N,n,YES,yes,NO,no" >&2;; esac |
[macg@mac-home ~]$ sh test.sh enter y/n : no |
注意::
如果有多个单词可以用"|"隔开,如
case $yn in
start | begin ) return 0;;
end | over ) return 1;;
* ) return 3;;
if, case,匹配字符串最常见,但如何匹配一段很长的输出,一堆文字?最好方法,用“*”,如:*"command not found"*
[macg@machome ~]$ vi test.sh |
[macg@machome ~]$ sh test.sh 22.txt |
这里需要注意的是:$(ls -l $1)
$()取命令输出
匹配是用两个**,因为整个var的内容是一行,要在两个之间匹配
例2.匹配file命令输出的一堆文字,以获知文件类型
用’ ’ 取输出,然后用CASE+*对输出做修饰处理.
var=`file $1` ` `和$( )作用相同,是取命令输出 echo "output is $var" case $var in "$1: ASCII text"*) echo "this is a text file";; "$1: directory"*) echo "this is a directory";; 注意*在双引号外边 esac |
[macg@machome ~]$ sh test.sh 22.txt output is 22.txt: ASCII text this is a text file [macg@machome ~]$ sh test.sh test-dir output is test-dir: directory this is a directory |
最典型的shell case命令匹配命令行,用于sys v启动脚本的start|stop|restart|status处理
case "$@" in
($@ 字符串数组:以"参数1" "参数2" ... 的字符串数组形式保存所有参数
对于单个参数的情况,$@就是一个字符串)
start)
echo -n "Starting
firewall..."
。。。
echo "OK!"
exit 0
;;
stop)
echo -n "Stopping
firewall..."
。。。
exit 0
;;
restart)
$0
stop $0即执行原始程序
$0
start
;;
status)
clear
echo ">------------------------------------------"
iptables -L
echo ">------------------------------------------"
iptables -t nat
-L POSTROUTING
exit 0
*)
echo "Usage: $0
{start|stop|restart|status}"
exit 1
esac